Whether you have some lawn furniture that’s seen better days or a kid’s toy that has been worn down with use, knowing how to paint plastic means that you can give fresh life to a piece (rather than having to say goodbye too soon).
Plastic is one of the more difficult surfaces to paint because of its smooth surface, and plastic responds to temperature more easily by expanding and contracting, so it’s more prone to cracking or flaking over time.
By taking a little extra care, you can get a new paint job that looks great (and will last longer) than if you rush through the process and skip right to the painting.
Check out our other helpful tip posts with …
- How to Clean Brass
- How to Clean a Cast Iron Skillet
- How to Care for Monstera Plants
- How to Clean Makeup Brushes
I painted my daughter’s plastic slide on the DIY Mid-Century Play Set Makeover I did for her, and this plastic gets the most beating of any possible item. It sits directly in the sun, so there’s a lot of swelling and shrinking with the weather.
Plus, it’s outside in the winter and all the other elements, and has kids literally sliding down and climbing up it almost every day. It takes a beating, but it’s easy to refresh the paint as needed.
And when you paint a plastic object that’s indoors or used more gently in a covered space, well, you can imagine how much longer the paint job stays pristine.
Prepping your area before painting: Spray painting is always best done outside whenever possible because of fumes and overspray. Check the paint can for the temperature requirements so that it’s not too cold for the paint to set properly.
Put down a tarp, plastic sheet, or a large piece of cardboard so your lawn/patio will be protected—paint soaks into cardboard easily, so that’s what I usually use.
Paint Tip! If there are areas you don’t want to paint (or want to paint a different color), tape off those areas with painter’s tape or wrap plastic around those spots and use painter’s tape to keep the plastic in place.
Frequently Asked Questions
Do you need to prime plastic before painting?
Even though there are paints out there with a primer already included, when painting plastic it’s a good idea to use a plastic-specific primer first for best adhesion. Do it after the surface is roughed up a bit with sandpaper and cleaned, and apply it in even light coats.
Supplies:
- fine sandpaper (180 to 220 grit should be good)
- scrub brush
- mineral spirits or isopropyl alcohol
- rags
- plastic-specific primer
- plastic-specific spray paint
Frequently Asked Questions
Do you need to use a special paint for plastic?
Yes! Most paints will say clearly what materials they are intended for, but there are a few that are specifically formulated more towards plastics, so you’ll want to use one of those.
Lines like Krylon Fusion, Rust-Oleum Universal, and Rust-Oleum Painter’s Touch 2X Ultra Cover are some of the most popular choices.
Step one: Clean off the surface with a scrub brush. Using it dry first will remove any loose or flaking paint if the item has been painted before, and going over it again with some soapy water will remove dirt on the surface as well.
If the item is outdoor furniture, you may need a little elbow grease to get off areas that have mildew or algae growing.
Step two: Sand your item with fine grit sandpaper. Since most plastic is smooth, you want to rough up the surface a bit to give the paint something to stick to.
Fine sandpaper will rough up the smooth surface without leaving visible sanding marks, so make sure to keep it to a fine grit.
Step three: Remove sanding dust. Now that your item has a rougher surface, make sure to clean off all the sanding dust so that there’s no barrier between the paint and the item so they can properly adhere.
Use a dry cloth first to get the bulk of the dust and then use a wet rag with mineral spirits or isopropyl alcohol to trap the final particles.
Step four: Paint with primer. Lay your item flat onto your cardboard or tarp and spray it with thin even coats of primer.
Keep going in one direction in a close zig-zag pattern (don’t go backwards where you already sprayed). Allow it to fully dry according to the can directions before proceeding.
Paint Tip! Spray a test item first to make sure paint is mixed well enough or isn’t past it’s shelf life if it’s one you’ve had for a bit. Sometimes the nozzles on spray cans can get clogged, which you can usually fix by taking off the nozzle and soaking in mineral spirits or paint thinner for a few hours before putting it back on.
If you just start spraying your item right away, you may get a chunky thick spray that you can’t really fix once it’s on, so it’s better to test it first to make sure it’s spraying smoothly and evenly.
Step five: Spray paint with your final color. Plastic isn’t absorbent, and it doesn’t soak up paint like most materials, so you really have to do more coats of light coverage to avoid drips.
Have patience and do one light coat at a time, waiting the proper dry time between coats according to the paint directions, until your whole item is covered evenly.
Paint Tip! Make sure not to spray too closely! Hold the can 8-12″ away from the item and tilt down at a 45° angle to spray light coats.
How to Paint Plastic Painting Tips:
- If the item is something that is handled or sat on, wait several days to let it totally cure before using.
- If you feel like there’s a slight roughness to the paint in spots, you can use an extra fine sandpaper to gently smooth out those spots in a light circular motion when the paint is 100% dry. Then, wipe the paint dust away with a dry and then a wet cloth (just wet with water).
- Make sure to shake the paint can every so often to keep it mixed evenly.
- Once you are down to the end of the can, don’t use the very last of the paint. It tends to come out chunky near the end, so just leave the last bit in the can.
There you have it! Now you can be your own plastic painting expert and refresh the plastic items in your home to give them a whole new life. xo. Laura
Love this post? Sign up for our newsletter for more ideas!
Get creative ideas for recipes, crafts, decor, and more in your inbox!
Get the How-To
Supplies
- fine sandpaper
- scrub brush
- mineral spirits or isopropyl alcohol
- rags
- plastic-specific primer
- plastic-specific spray paint
Instructions
- Step one: Clean off the surface with a scrub brush. Using it dry first will remove any loose or flaking paint if the item has been painted before, and going over it again with some soapy water will remove dirt on the surface as well. If the item is outdoor furniture, you may need a little elbow grease to get off areas that have mildew or algae growing.
- Step two: Sand your item with fine grit sandpaper. Since most plastic is smooth, you want to rough up the surface a bit to give the paint something to stick to. Fine sandpaper will rough up the smooth surface without leaving visible sanding marks, so make sure to keep it to a fine grit.
- Step three: Remove sanding dust. Now that your item has a rougher surface, make sure to clean off all the sanding dust so that there’s no barrier between the paint and the item so they can properly adhere. Use a dry cloth first to get the bulk of the dust and then use a wet rag with mineral spirits or isopropyl alcohol to trap the final particles.
- Step four: Paint with primer. Lay your item flat onto your cardboard or tarp and spray it with thin even coats of primer. Keep going in one direction in a close zig-zag pattern (don’t go backwards where you already sprayed). Allow it to fully dry according to the can directions before proceeding.
- Step five: Spray paint with your final color. Plastic isn’t absorbent so it doesn’t soak up paint like most materials, so you really have to do more coats of light coverage to avoid drips. Have patience and do one light coat at a time, waiting the proper dry time between coats according to the paint directions, until your whole item is covered evenly.
Notes
How to Paint Plastic Painting Tips:
- If the item is something that is handled or sat on, wait several days to let it totally cure before using.
- If you feel like there’s a slight roughness to the paint in spots, you can use an extra fine sandpaper to gently smooth out those spots in a light circular motion when the paint is 100% dry and then wipe the paint dust away with a dry and then a wet cloth (just wet with water).
- Make sure to shake the paint can every so often to keep it mixed evenly.
- Once you are down to the end of the can, don’t use the very last of the paint. It tends to come out chunky near the end, so just leave the last bit in the can.
So I need to sand paper those sterlite 3 drawers before I spray paint???
THANK YOU For this tutorial! I started on a playhouse last year, with a fair amount of prep, but I didn’t sand or prime. The glossy shutters peeled and look awful, but the matte roof and wall have held up through the elements. I have a “vision” and plan to try again next spring when my littles are a bit better at playing while I work on it and watch them. Few questions:
– Did you do a protective clear coat?
– How long do you think this would/should last? If I do the proper sanding/priming, I would hope to get three years out of it (somewhat protected patio location).
– I also have a small slide I wanted to do, but figured it may not “slide” well… is yours still slick?
This is my first comment on a blog post after following for a while. Love your whole team! <3
Yes, matte paint can definitely hold up better than a super glossy one but sanding and priming should help a ton! I didn’t use a clear coat but it doesn’t hurt to add one that’s an exterior sealer.
It’s really hard to guess how long it would last outside based on not knowing your use level or weather conditions, but if it’s in a somewhat protected spot and snow and rain isn’t piling up on it along with direct sunlight constantly, then a few years is definitely possible.
If the slide doesn’t feel “slick” enough after painting, I like to lightly buff mine with a super fine sandpaper until it feels smooth and wipe away the sanding dust before she slides down it and it works like a charm! Good luck!
When you say super fine, what number grit do you think? And should you use wet and dry or is there paint sandpaper?